Safety Wash CRC™ is a revolutionary concept in chemical cleaners for all phases of cleaning. Safety Wash™ CRC can be used in dip tank, wipe down and in both high and low pressure spray applications. In addition to its proven cleaning properties, Safety Wash™ CRC is biodegradable, economical and environmentally safe. Safety
Wash™ CRC will not corrode or pit aluminum, copper, brass or other sensitive metals.
Safety Wash™ CRC has literally hundreds of proven uses and is considered to be a major breakthrough for aerospace, industrial, marine and off-shore applications. Safety
Wash™ CRC is recommended to be utilized in diluted form but can be used at full strength without safety hazards or concerns.
Safety Wash™ CRC has been field tested and proven as safe alternative for ozone depleting substances in metals cleaning. Safety
Wash™ CRC is listed in the Hazardous Solvent Substitution Data System (HSSDS) as a replacement for hazardous chemicals in cleaning applications.
Safety Wash CRC leaves absolutely no film or residue. Leaves surfaces ready for painting. Dilutions vary with degree of cleaning necessary. Pre-testing is recommended.
Product Features
- Cleans fluorocarbons
- Removes Krytox™ and Braycote™
- Non-corrosive
- Removes silicones
- Emulsifies grease and oil
- Biodegradable as manufactured
- No petroleum additives
- No volatile components
- Aqueous based cleaner
- Removes low & medium molecular weight hydrocarbons
- Low NVR
- HSSDS listed
- No flash point
- Non-toxic
- OSHA accepted
- No chlorinated solvents
- No glycol ethers
- No halogens
- No phosphates
- No noxious odors
Typical Properties of Safety Wash CRC
| None |
| None |
| 210ºF |
| None |
| 25ºF |
| 1.02 pH (as is) 11 to 12 |
| Non-toxic |
| Up to 50:1 (10 - 20:1 optimal) |
| None |
| Complete in hard or soft, fresh or saline water |
| Buffered alkaline blend of biodegradable non-ionic surfactants |
AMS 1526B
Boeing D6-17487 Revision M
Douglas CSD #1, Type I |
Suggested Uses for Safety Wash CRC
| Cleaning Type |
Dilution Table |
Suggested Uses |
| Normal Cleaning |
10 to 20:1 |
Flush shop floors and walls
Smoke stack exhaust
Oil-soaked ground & beach sand
Mold; Mildew; Algae; Water-line scum
Vinyl; Decks; Teakwood
Air conditioner filters
Shower stalls; Bathtubs; Sinks
Coolant systems
Carpeting
|
| Heavy-Duty Cleaning |
5 to 10:1 |
Ramps; Decks; Platforms
Engine rooms
Oil stained concrete
Commercial kitchens
Galleys; Bulkheads; Valve bodies
Petroleum-based drilling muds |
| Extra-Heavy Cleaning |
5:1 |
Holding tanks
Engines
Carbon on engine heads
Petrolatum; Bunker C oil; #6 Crude oil
Grease traps |
Steam Cleaning/
Pressure Washing |
5 to 100:1 |
Steam cleaning - Hot or Cold
Pressure wash - Hot or Cold |
AMS 1526B Information for Safety Wash CRC
AMS 1526B
Cleaner for Aircraft Exterior Surfaces
Water-Miscible, Pressure Spraying Type |
| Rating: 1 |
| <0.01 mg/cm²/24hrs weight loss |
| 0.06 mg/cm² diluted / 0.30 mg/cm² as is |
| No failures within 150 hours |
| No flash to 141ºF |
| Pass |
| Conforms |
| Conforms |
Boeing D6-17487 Rev. M Information for Safety Wash CRC
Boeing D6-17487 Rev. M
Exterior and General Cleaners
Liquid Waxes, Polishes and Polishing Compounds |
| Rating: 1 |
| No crazing, cracking or etching |
| <1 Pencil hardness change after 24 hours |
| No failures within 150 hours |
Douglas CSD #1, Rev. 8/2/98 Information for Safety Wash CRC
Douglas CSD #1, Rev. 8/2/98
Type I: Materials and Procedures for General Exterior
of Painted and Unpainted Surfaces |
| No softening or discoloration after 24 hours |
| AMS 4911: Pass AMS 4049: Pass |
| Rating: 1 |
| No crazing, cracking or etching |
| 0.1 mg diluted / 0.2 mg as is after 168 hours |
| 1.8 mg diluted / 8.5 mg as is after 24 hours |
| No failures within 150 hours |
