Kramer Industries Inc. > Blast Room Package Accessories

55 Gallon Dust Drum Package

Designed for continuous duty blasting operations. Provides optimum dust filtration efficiency with minimum maintenance. Cartridge filters are automatically pulsed clean during operation. Dust is stored in sealed 30 or 55-gallon drum.

The Dust Drum Package is designed for continuous duty blasting operations. It provides optimum dust filtration efficiency with minimum maintenance. Cartridge filters are automatically pulsed clean during operation. The dust is automatically collected and stored in a sealed 55-gallon drum.

55 Gallon Dust Drum Package

Dust Collector shown with 55 Gallon Dust Drum Package

  • 1500 CFM Rated airflow
  • Two high-efficiency cartridge filters
  • 472 Square feet total surface filter area
  • 99.7% efficiency to 0.5 microns
  • Automatic reverse-pulse cartridge cleaning
  • Magnehelic pressure sensing gauge
  • 5 HP, 230/460V 3Phase motor
  • 30-gallon steel dust drum with lid
  • Adjustable air flow damper
  • Exhaust fan silencer
  • 110 Volt sequencer
  • 30 or 55-gallon drum available

 

Air Fed Helmet Package

Air Fed Helmet, Air Line Filter, 50′ Air Hose

helmet-line-hose copyHelmets are designed for operations in blast cleaning rooms, inside of tanks and other confined areas and are required on many open-air operations of heavy duty and lengthy work periods to meet OSHA standards. Made of refined, the helmet is a one-piece molded high-density polyethylene with special coated nylon cape for durability. Adjustable dihedral headband suspension affords user sizing range comfort. Hinged gasket-sealed vision frame affords maximum vision range with easy change of vision lens.

Connecting to the air compressor: The 600HP air supplied helmet is designed for use with the air line filter and should be connected to a standard air compressor using the 3/8” Air Hose. We recommend using an electric compressor to ensure that no toxic gases are present in the air stream. If a gas or diesel compressor is being used, we highly recommend using the carbon monoxide monitor as a safety precaution.

Connecting to the electric air pump: The 600LP air supplied helmet is designed for connection to the oil-less air pump and should be connected using the 1/2” air hose. The air pump should be placed in a clean, breathable location so no toxic gases are present in the air stream.

 

Compressed Air Line Filter Assembly

Type “A” air line filter assembly provides clean breathing air to the user because it removes dusts, moisture, oil, fumes and scale from compressed air. Meets ASME Code requirements. Its component compounds are entirely separate from the water and oil condensation changer to prolong the life of the replaceable filtering compound unit. Type “A” air line filter assembly is recommended for all air supplied helmets and has a capacity to afford clean breathing air to as many as six helmets.

Caution: Compressed air line filters do not remove carbon monoxide.

Oil-less Air Pumps

air-pump

The oil-less air pump is available for one operator with a 3/4 HP electric motor. This air pump is designed for NIOSH approved air supplied helmets that operate at 10 psi or less. The inlet must be placed in a clean, breathable location, free from exhausts, fumes and dust. The air pump will not remove carbon monoxide or toxic gases from incoming air pumps to the helmets. The air pump requires a 110-115V, 60Hz, 14 amp power supply and has an air outflow of 9 cfm at 10 psi. The 600LP air supplied helmet used with the air pump and is connected using the 1/2” air hose. No compressor is necessary when using the oil-less air pump and 600LP air supplied helmet.

Carbon Monoxide Monitor

The ISA-34RAL respiratory air line CO monitor/alarm automatically and continuously monitors respiratory air lines for carbon monoxide levels and provides audible and visual alarms when the air line CO concentration rises above a preset limit. When the level of CO in the air passing the sensor increases to the preset value, the equipment alarms and relays activate. The preset calibration level may be as low as 20 PPM. The equipment operates from either 117 VAC or 12 VDC, at the option of the user, with terminals for either mode of operation located on a barrier strip inside the unit. Due to its electronic voltage regulation, the ISA-34RAL maintains precision gas calibration despite input voltage variations as great as -10% to +20% of rated supply (either AC or DC).

When a project needs finishing, start here. The last stop for all your surface finishing needs.